Hardened Steel vs Stainless Steel vs Brass Nozzles: Which One Your Filament Needs
Owen Hartley
November 20, 2026
You have a spool of carbon fiber PETG, a glow-in-the-dark PLA for a gift, or a wood-fill you want to try, and the product page says “hardened nozzle recommended.” Your printer came with something else, or you are not sure what it came with. Before you buy a replacement, it helps to know what the nozzle material actually changes: how fast it wears, how well it moves heat into the filament, and what you give up when you swap brass for steel or something more exotic.
This guide walks through brass, stainless steel, hardened steel, tungsten carbide and ruby-tipped nozzles, what the major printer makers ship as standard, and which filaments genuinely need an upgrade.
Why the nozzle material matters at all
A nozzle does two jobs. It has to transfer heat from the heater block into the filament fast enough to melt it at your print speed, and it has to keep a precise, round opening while plastic is pushed through it for hundreds of hours. Different metals are good at one job or the other, rarely both.
Heat transfer depends on thermal conductivity. Wear resistance depends on hardness. Brass sits at one end: it conducts heat very well but is soft. Hardened steel sits at the other: it resists abrasion far better but conducts heat poorly. Most of the decisions in this article come down to where on that line your filament forces you to be.
Thermal conductivity: brass leads, steel lags
Published figures vary between vendors and alloys, but they cluster in clear groups. Nozzle listings from suppliers such as McMaster-Carr and FlashForge put brass at roughly 105 to 117 W/m·K. Stainless steel (commonly 303 grade in nozzles) is listed around 16 W/m·K, and hardened tool steel nozzles at roughly 15 to 25 W/m·K. Tungsten carbide is the awkward one: depending on grade and binder content, sources quote anywhere from about 40 to over 160 W/m·K, so check the datasheet for the specific nozzle.
In practice, a steel nozzle needs a little more heat to deliver the same melt. Prusa’s product page for its hardened steel E3D V6 nozzle says you may need to raise the hotend temperature by about 5 °C. E3D, describing its older Nozzle X hardened steel line, put the figure at around 10 °C to match brass results. Prusa’s documentation also notes that some standard materials, ABS among them, cannot be printed as fast through hardened steel as through a regular nozzle.
That is why many people see slightly duller surfaces, underextrusion on fast infill, or weaker layer bonding right after swapping to steel. The fix is usually to raise the temperature by 5 to 10 °C or lower the maximum volumetric speed in your slicer, then run a fresh flow calibration. Exact numbers vary by filament brand, so start from the range on the spool label and adjust from there.
Which filaments actually wear a nozzle out
Ordinary PLA, PETG, ABS, ASA, TPU and unfilled nylon do not meaningfully wear a brass nozzle. The problem is hard particles mixed into the plastic. Prusa’s help center and Bambu Lab’s wiki both list the usual suspects:
- Carbon fiber and glass fiber filled filaments such as PLA-CF, PETG-CF, PA-CF, PAHT-CF and PET-CF. Glass fiber is generally the harsher of the two.
- Glow-in-the-dark filaments, which contain hard phosphorescent pigment particles. Prusa lists them alongside carbon-filled materials as abrasive, and its nozzle guide names glow-in-the-dark materials among the targets for its most wear-resistant ObXidian 500 option.
- Metal-filled filaments such as bronze, brass or copper fill. Prusa specifically names Bronzefill and Brassfill.
- Some wood-filled filaments. Wood fill is less abrasive than fiber, and clogging is often the bigger concern. Bambu Lab’s guidance for its own Wood PLA suggests a hardened steel nozzle in 0.4, 0.6 or 0.8 mm to reduce clogging, says a 0.4 mm stainless nozzle is also acceptable, and rules out 0.2 mm.
A brass nozzle running these materials can lose its round opening quickly. The symptoms build up gradually: underextrusion that calibration does not fix, a wider and messier line, and a nozzle tip that looks visibly worn when inspected. Bambu Lab’s P1S upgrade documentation warns that stainless steel components can also wear out quickly with carbon fiber, glass fiber, metal-filled and glow-in-the-dark filaments, which surprises people who assume “steel is steel.”

Brass, stainless, hardened steel, tungsten carbide and ruby compared
The table below summarizes the trade-offs. Conductivity figures are approximate ranges drawn from vendor listings; prices are typical US retail at the time of writing and change often.
| Nozzle material | Heat transfer | Abrasion resistance | Best for | Typical drawback |
|---|---|---|---|---|
| Brass | Excellent (about 105–117 W/m·K) | Low | PLA, PETG, ABS, ASA, TPU, unfilled nylon | Wears quickly with filled filaments |
| Stainless steel | Poor (about 16 W/m·K) | Low to moderate | Common non-abrasive filaments; food-adjacent projects | Not a real answer for CF/GF or glow filaments |
| Hardened steel | Poor (about 15–25 W/m·K) | High | CF/GF-filled, glow-in-the-dark, metal and wood fill | May need about 5–10 °C more and lower top flow |
| Coated or composite (e.g. ObXidian) | Close to brass, per E3D | High | Mixed abrasive and normal printing | Costs more than hardened steel |
| Tungsten carbide | Varies widely by grade | Very high | Heavy abrasive use, print farms | Roughly $60–85 per nozzle for Bambu’s H2/P2S version |
| Ruby-tipped (Olsson Ruby) | Good (brass body) | Very high at the tip | Long-term abrasive printing on compatible hotends | Around $90 list; limited hotend compatibility |
What Bambu Lab and Prusa ship as standard
Knowing your stock nozzle tells you whether you need to buy anything at all.
Bambu Lab
- A1 and A1 mini: Bambu Lab’s A1 FAQ states the printer comes with a 0.4 mm stainless steel nozzle and says you can print carbon- or glass-filled filaments after swapping to a hardened steel nozzle. Bambu sells hardened steel hotends for the A1 series in 0.4, 0.6 and 0.8 mm.
- P1S: Bambu Lab’s wiki says the P1S ships with a stainless steel hotend and stainless extruder gears, and recommends a hardened steel hotend plus hardened extruder upgrade for abrasive filaments.
- P2S: Bambu Lab’s P2S specifications list a hardened steel nozzle as standard, with 0.2, 0.4, 0.6 and 0.8 mm sizes supported and a 300 °C maximum. That is one of the practical differences covered in our P2S vs P1S comparison.
- X1 Carbon: ships with a hardened steel 0.4 mm nozzle, so it handles filled filaments out of the box.
One detail catches people out: Bambu printers do not detect nozzle material automatically. After a swap, set the nozzle type and diameter on the printer or in Bambu Handy, and select the matching nozzle in your slicer, so filament compatibility warnings and flow profiles are correct. If you use a third-party slicer, our OrcaSlicer vs Bambu Studio guide explains where those printer settings live.
Prusa
Prusa’s help center states that Prusa printers ship with brass nozzles. The CORE One+ product page lists a high-flow brass CHT 0.4 mm nozzle in the box. Nextruder printers (CORE One, MK4S, XL) use Prusa’s quick-swap Prusa Nozzle system, and Prusa’s nozzle guide lists a wide range of options for it:
- Prusa Nozzle Brass and Brass CHT for everyday non-abrasive printing. Prusa does not recommend the CHT or high-flow variants with the MMU3.
- Prusa Nozzle ObXidian, described as hardened steel with a corrosion-resistant coating, for carbon fiber and high-temperature work. Prusa advises against cold pulls with it.
- Prusa Hardened Nozzle (nickel plated) for printers that switch often between abrasive and normal filaments.
- E3D High Flow ObXidian and ObXidian 500 variants, with E3D claiming the 500 has at least five times the wear resistance of standard ObXidian.
- E3D DiamondBack, with a solid polycrystalline diamond tip, aimed at metal- and ceramic-filled engineering filaments.
If you are deciding between these two ecosystems more broadly, our Prusa Core One vs Bambu Lab P2S comparison covers the rest of the picture.
Hardened steel vs stainless steel: not the same upgrade
This is the comparison people search for most, and the two are easy to confuse because both are steel and both are grey or dark. They solve different problems.
Stainless steel resists corrosion and does not contain the lead often added to free-machining brass. It is a reasonable default for a budget printer, but it is not particularly hard. Bambu Lab’s own documentation warns that stainless parts wear quickly with filled filaments.
Hardened steel is heat-treated tool steel. It is much harder and is the baseline recommendation from both Prusa and Bambu Lab for abrasive materials. It does not resist corrosion as well, which is why some versions add nickel plating or another coating. A practical tip from Bambu’s community: hardened steel nozzles are typically black and magnetic, while stainless ones are grey and not magnetic, which helps if you have lost track of which hotend is which.
If your goal is printing CF or GF filaments, choose hardened steel or better. If your goal is reducing what a worn brass nozzle sheds into a print, stainless is the usual pick.

Food-contact claims and stainless nozzles
Stainless nozzles are often marketed as “food safe.” That claim deserves caution. Prusa’s food-safe FDM article says the standard brass nozzle is not considered food-safe because it wears and the worn material ends up in the print, and that you would need a stainless steel or titanium nozzle if you are even considering printing with food in mind.
The nozzle is only one part of the problem. The filament itself, colorants, the extruder path and especially the layer lines, which can trap food residue and bacteria, all matter. Polymaker points out that the FDA does not offer a specific certification for 3D printing materials. Treat a stainless nozzle as a necessary step, not proof that a printed cup or cutter is safe. For anything that touches food, read our safety disclaimer and consider sealing the part with a coating rated for food contact, or using the print only as a mold or for short, dry contact.
Tungsten carbide, ruby and other premium tips
Once you print abrasive filaments regularly, hardened steel itself becomes a consumable. Premium materials trade a higher upfront price for a much longer life.
Tungsten carbide
Tungsten carbide is extremely hard and, depending on the grade, can conduct heat far better than steel. Bambu Lab now offers tungsten carbide nozzles and high-flow tungsten carbide nozzles for its H2-series and P2S printers. US and Canadian retailer listings at the time of writing put the standard version at roughly $63 to $85 per nozzle, with high-flow versions higher. Prices vary depending on whether you are buying a bare nozzle or a complete hotend.
Ruby-tipped nozzles
The Olsson Ruby from 3DVerkstan pairs a brass body with a ruby tip. The brass body keeps heat transfer good, while the ruby handles the abrasive wear at the opening. Prusa lists it at $90, a high-temperature version lists at around $150, and retailers frequently discount both. The catch is compatibility: it is made for V6-style and similar hotends, not for Bambu Lab’s integrated hotends. Nextruder owners would need Prusa’s V6 nozzle adapter.
Coated composite nozzles
E3D’s ObXidian line uses a hardened steel insert in a copper-alloy body with a diamond-like carbon coating. E3D says this means you do not need to raise temperatures the way you do with plain hardened steel. Retail prices for V6 and Volcano versions are typically in the $50 to $70 range, with Nextruder high-flow variants costing more.
Nozzle size and abrasive filaments
Material is only half the decision. Filled filaments contain fibers or particles that can bridge across a small opening and clog it. Bambu Lab’s wiki notes that going from 0.4 mm to 0.6 mm and 0.8 mm reduces print fineness but also lowers the chance of clogging. Bambu’s store recommends a hardened steel 0.6 mm nozzle for general carbon or glass fiber filaments such as PAHT-CF and PET-CF, while saying its own PLA-CF and PETG-CF have tested with a low clogging risk on 0.4 mm hardened steel.
A few rules of thumb follow from that guidance:
- Avoid 0.2 mm nozzles with any filled filament. Bambu explicitly rules out 0.2 mm for its Wood PLA.
- Use 0.6 mm as a safe default for engineering CF and GF filaments, especially nylons.
- Larger nozzles push more plastic per second, which makes the reduced heat transfer of steel more noticeable. Lower the volumetric speed if you see underextrusion.
- Dry filled filaments before printing. Many are nylon or PETG based and absorb moisture readily.
Matching the nozzle to what you actually print
Use your filament shelf, not the marketing, to decide:
- Only PLA, PETG, ABS, ASA and TPU: keep brass if you have it. It transfers heat best, it is cheap to replace, and it gives the best surface at high speed. A stock stainless nozzle on a Bambu A1 or P1S is fine for these too.
- Occasional CF PLA, glow-in-the-dark or wood fill: buy a hardened steel nozzle and swap it in when needed. On a P1S, Bambu also recommends hardened extruder gears.
- Regular abrasive printing: a printer that ships hardened, such as the P2S or X1 Carbon, saves the swap. Otherwise make hardened steel your default and expect to replace it periodically.
- Heavy abrasive use or print farm duty: tungsten carbide, ObXidian 500, ruby or DiamondBack can be cheaper over time than repeatedly replacing hardened steel.
- Food-adjacent projects: stainless steel is the conventional nozzle choice, but the nozzle alone does not make a part safe for food.
Whichever material you choose, re-run flow calibration after a swap. Small changes in nozzle material shift how much plastic actually leaves the tip at a given setting.