How to Fix Stringing in 3D Prints: Retraction, Temperature and Wet Filament

Marco Ellis

Marco Ellis

November 19, 2026

How to Fix Stringing in 3D Prints: Retraction, Temperature and Wet Filament

You pull a print off the plate and it looks like it was wrapped in cobwebs: fine hairs between two towers, a thick strand across a gap, or little bumps where the nozzle started and stopped. The part is usable, but cleaning it up takes longer than printing it did. Stringing is one of the most common print defects, and the most common fix people try first, turning retraction up, often does less than you would expect. This guide works from diagnosis to fixes, in the order that usually pays off fastest.

What stringing and oozing actually are

Bambu Lab’s wiki draws a useful line between two related defects. Stringing is the thin strands of plastic pulled out of the nozzle during travel moves, leaving cobweb-like threads on the surface or between parts. Oozing is molten plastic that keeps leaking when the nozzle should not be extruding, which shows up as local blobs, buildup on the nozzle and surface defects. Bambu lists the shared causes as excessive extrusion at the nozzle, damp filament and incorrect retraction settings. Prusa’s knowledge base puts it more bluntly: the root cause is usually printing temperatures that are too high, retraction settings that are wrong, or both.

The hotend is full of molten plastic under pressure, and anything that seeps out during a travel move gets stretched into a strand. Retraction pulls filament back to relieve that pressure; temperature and moisture decide how runny the plastic is in the first place.

Identify which kind of stringing you have

The shape of the defect points to the likely cause, which saves you from tuning the wrong thing.

Fine wisps and “hairy” prints

Very thin, almost weightless hairs that break when you brush them are usually a sign that the plastic is too runny or contains moisture. Wisps that persist across a whole spool, even with reasonable retraction, point toward temperature and drying before anything else.

Thick strings across gaps

Strands with real substance, often bridging the gap between two separate objects, suggest that a meaningful amount of plastic is leaving the nozzle during long travel moves. Bambu’s wiki ties this to long travel distances combined with too little retraction, and to plates where models are spaced far apart. Retraction and travel settings are the main levers here.

Blobs, zits and popping sounds

Small bumps where a perimeter starts or ends, rough patches, and audible popping or visible bubbles from the nozzle are classic signs of wet filament. Bambu’s drying guide lists popping sounds, bubbles during extrusion, increased stringing and rough surfaces as reasons to dry a spool before printing. If you hear crackling as the filament extrudes, skip straight to drying.

Step 1: Dry the filament before touching any setting

Bambu’s retraction documentation makes the case for this order directly: damp filament is more prone to stringing and oozing, and that usually cannot be fully solved by adjusting retraction alone. Dry first, then tune. Moisture turns to steam in the hot nozzle, the melt expands and flows unevenly, and you get strings no matter how carefully you retract.

All filaments absorb some moisture, but some are far more sensitive. Bambu’s guide names TPU, PETG, PLA Wood, PC, PVA and several carbon-fiber blends among the hygroscopic materials that should be dried before printing. Prusa’s knowledge base suggests a simple diagnostic: if you suspect moisture, try a different spool of the same material. If the fresh spool prints clean with identical settings, the old one needs drying.

Drying temperatures and times depend on the material and the equipment you own, and they vary by brand, so check the label or the maker’s datasheet. Our guide on how to dry filament, including dryers and the AMS covers temperatures by material. After drying, store the spool sealed with fresh desiccant, as Bambu recommends, or you will be back to stringing within days in a humid room.

A printer nozzle close above a blue printed part

Step 2: Lower the nozzle temperature with a temperature tower

Hotter plastic is less viscous and leaks more readily during travel. Bambu’s wiki lists an excessively high nozzle temperature as a cause of stringing, and Prusa’s knowledge base suggests lowering the nozzle temperature by 5–10 °C and checking the result. The goal is the coolest temperature that still gives strong, well-bonded layers.

Rather than guessing, print a temperature tower: a model divided into bands, each printed at a different temperature. OrcaSlicer has one built in under its Calibration menu (Calibration, then Temperature). For other slicers, community temperature towers on Printables and MakerWorld usually include instructions for setting the temperature changes in that slicer. Pick the band with the least stringing that still has good surface quality and solid layers, then save that value in your filament profile.

Start from the range on the spool or the maker’s datasheet, since brands differ. For reference, Bambu Lab’s filament guide lists nozzle ranges of 190–240 °C for standard PLA and 240–270 °C for its PETG, with PETG HF at 230–260 °C; other makers publish their own figures.

Step 3: Tune retraction distance and speed

Retraction works best once the filament is dry and the temperature is sensible. Two numbers do most of the work: how far the filament is pulled back and how fast.

Retraction distance: direct drive versus Bowden

The right distance depends heavily on where the extruder sits. On a direct-drive printer, the extruder is mounted on the print head, so there is very little slack between the gears and the nozzle. On a Bowden printer, filament travels through a long PTFE tube, and the extruder has to take up slack before it pulls anything out of the hotend.

  • Direct drive: Bambu Lab’s wiki generally recommends keeping retraction length no greater than 2 mm, warning that excessive retraction can easily cause clogging. Prusa’s knowledge base gives the same 2 mm maximum for the MK2.5 and MK3 families. OrcaSlicer’s retraction test defaults to a 0–2 mm range, which its wiki describes as suitable for most direct-drive extruders, and notes that low-oozing materials such as PLA or ABS may need only around 0.2–0.4 mm.
  • Bowden: OrcaSlicer’s wiki suggests widening the test range to 1–6 mm with a 0.2 mm step. Prusa’s presets for the Bowden-fed MINI and MINI+ default to 3.2 mm, which shows how much higher Bowden values tend to run.

More is not better. Bambu’s documentation warns that retraction set too high, or triggered too often, can cause under-extrusion, gaps between layers and clogs.

Retraction speed

A faster retraction relieves pressure before the nozzle starts moving. Prusa’s knowledge base says a higher retraction speed helps, but if it is too high the extruder motor may skip steps; UltiMaker’s Cura documentation adds that too fast can grind the filament. If you hear clicking from the extruder or see chewed filament after raising the speed, back it off.

Use OrcaSlicer’s retraction test to find the value

OrcaSlicer’s Calibration menu includes a Retraction test that prints a tower in which retraction length increases with height. Per the OrcaSlicer wiki, the defaults are a start of 0 mm, an end of 2 mm and a 0.1 mm step. After printing, find the cleanest section, measure its height, and look it up in the G-code preview by searching for the Calib_Retraction_tower comment. The wiki recommends choosing the shortest length that gives a clean result. It also notes that if the top of the tower still strings heavily, you should dry the filament and check that the nozzle is installed properly without leaks.

OrcaSlicer’s calibration guide places the retraction test after flow rate and pressure advance calibration. Over-extrusion leaves extra plastic in the nozzle, so getting flow right first gives retraction a fair chance. If you are deciding between the two Bambu-compatible slicers, our comparison of OrcaSlicer vs Bambu Studio covers which calibration tools each one includes.

Step 4: Shorten and hide the travel moves

Every travel move that crosses open air or an outer wall is a chance to leave a string. Several settings change where and when the nozzle travels.

  • Avoid crossing walls or perimeters. Bambu’s wiki recommends enabling Avoid crossing wall to reduce stringing. OrcaSlicer calls it Avoid crossing walls, and PrusaSlicer calls it Avoid crossing perimeters. All three route travel inside the part where possible, so any ooze lands inside rather than on the visible surface. The trade-off is longer travel and slightly longer print times.
  • Combing in Cura. Cura’s equivalent is Combing Mode, with options of Off, All, Not on Outer Surface, Not in Skin and Within Infill. UltiMaker describes combing as keeping travel moves inside the print’s boundaries. Avoid Printed Parts When Traveling routes the head around parts already printed.
  • Travel distance threshold. Retraction only fires when a travel move is longer than a minimum distance. Bambu’s wiki explains that on models with small gaps, short moves may not trigger retraction, so strings form between them; adjusting the threshold fixes that. PrusaSlicer calls this Minimum travel after retraction (its knowledge base notes a 1 mm preset and warns that higher values increase stringing), and Cura calls it Retraction Minimum Travel.
  • Wipe while retracting. Bambu describes the wipe as moving the nozzle along the last extrusion path while retracting to clean leaked material, which reduces blobs at the start of the next segment. Prusa’s knowledge base recommends keeping both wipe and retract on layer change enabled.
  • Spacing between models. Bambu’s wiki suggests reducing the spacing between models on a crowded plate, since shorter travel means less time for plastic to leak.

Tweezers pulling thin plastic strings off a small grey print

The z-hop trade-off

Z-hop lifts the nozzle during travel so it does not drag across or knock the print. That protects the part, but lifting also stretches any ooze into a longer string. Prusa’s knowledge base notes that a lower lift value improves stringing, while disabling it entirely may let the nozzle hit the part. Bambu Studio and OrcaSlicer offer several z-hop types; Bambu’s wiki says slope, spiral and auto lift can effectively reduce oozing and stringing compared with a plain vertical lift. Cura ships with Z Hop When Retracted turned off by default. If you see strings that run diagonally upward from the surface, try a smaller hop or a slope or spiral type before turning it off.

Material-specific notes: PETG, TPU and specialty PLA

PETG strings more readily than PLA for most people. It prints hotter, it absorbs moisture, and it tends to stick to the nozzle. Prusa’s knowledge base adds that printing long runs of one material such as PETG can leave a thin residue inside the nozzle that keeps causing strings, and recommends cleaning the nozzle thoroughly and clearing out remnants of earlier filaments. Expect to accept a few fine wisps with PETG even after tuning. For more on how the two materials differ in practice, see PETG vs PLA.

TPU and other flexibles behave differently because the filament stretches. Prusa notes that flexible filaments usually need longer retraction and often considerable tuning. Bambu’s documentation adds a caution in the other direction: retraction on elastic materials can deform the filament and lead to clogs and extrusion problems. In practice, change retraction in small steps with flexibles, keep the filament dry, and lean more on temperature and travel settings.

Low-density PLA, such as Bambu PLA Aero, foams as it prints. Bambu’s wiki says to dry it, lower the print temperature, and set the flow ratio between 0.5 and 0.7 when slicing; without those adjustments it strings and oozes heavily.

Where to find the settings in each slicer

Setting names drift between versions, so use the search box in your slicer if a label does not match exactly.

Setting OrcaSlicer / Bambu Studio PrusaSlicer Cura
Retraction distance Printer settings, Extruder: Length (per-filament override in Filament settings, Setting Overrides) Printer Settings, Extruder 1: Retraction length Travel: Retraction Distance
Retraction speed Printer settings, Extruder: Retraction speed Printer Settings, Extruder 1: Retraction Speed Travel: Retraction Speed
Travel threshold Travel distance threshold Minimum travel after retraction Retraction Minimum Travel
Route travel inside parts Avoid crossing walls (Quality tab) Avoid crossing perimeters (Layers and perimeters) Combing Mode; Avoid Printed Parts When Traveling
Wipe Wipe while retracting Wipe while retracting Wipe Retraction Enable
Z-hop Z hop when retracting / Z-hop height, Z-hop type Lift Z (shown as Lift height in newer builds) Z Hop When Retracted
Nozzle temperature Filament settings Filament Settings, Filament Material: Printing Temperature

When settings are not the problem

If you have dried the filament, run a temperature tower and a retraction test, and strings persist, look at the hardware. Bambu’s wiki lists two nozzle-related causes: a slicer profile that does not match the nozzle actually installed (for example a 0.6 mm nozzle sliced as 0.4 mm, which over-extrudes), and a worn nozzle that should be replaced. Prusa’s knowledge base points to poor heat dissipation in the hotend, such as missing thermal paste on the heatbreak or heatsink threads or incorrectly assembled hotend parts. The OrcaSlicer wiki also mentions checking that the nozzle is seated without leaks.

For a print that is already done, Prusa suggests passing a heat gun at about 200 °C over the strings for one or two seconds; any longer and the part itself can deform.

Keep the fixes in your filament profile

Work in the order above: dry, then temperature, then retraction, then travel, then hardware. Change one thing at a time and print the same small test model after each change. Save the tuned temperature and retraction values in the filament profile rather than the printer profile, and revisit them only when you switch brands or a spool has been sitting open.

More articles for you